Mercedes M-Class W163

since 1997 of release

Repair and car operation



Mercedes W163
+ Mercedes-Benz Cars of a class M (W163)
+ Governing bodies and receptions of safe operation
+ Current leaving and service
- Engine
   Check of kompressionny pressure in cylinders
   Engine check by means of the vacuum gage
   Replacement of a belt of a drive of auxiliary units and elements of the mechanism of its tension
   + Petrol models
   - Diesel models
      Removal and engine installation
      Removal and installation of covers of a drive of GRM
      Replacement of a gas-distributing chain
      Removal and installation of components of a drive of GRM
      Installation of base provision of camshafts
      Verification of the base provision of a balancing shaft (only series 628 engines)
      Removal and installation of GRM components
      Removal and head installation (ok) cylinders
      Removal and installation of the electromotor of shutdown of inlet port (series 612 engine)
      Removal and installation of a final collector
      Replacement of a forward epiploon of a cranked shaft
      Removal and installation of a back face cover, replacement of a back epiploon of a cranked shaft
      Removal and installation of a damper krutilny fluctuations/pulley of a driving belt
      Removal and flywheel installation / driving disk
      Removal and installation of support of a suspension bracket of the power unit
      Service of system of greasing
+ Systems of cooling, heating and air conditioner
+ the Power supply system and production of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Avtomaticheckaya transmission
+ Transmission line
+ Brake and auxiliary systems
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment


Кирпичные столбы для забора

Removal and installation of a damper krutilny fluctuations/pulley of a driving belt

М612

Details of installation of a damper krutilny fluctuations/pulley of a driving belt of the engine of a series 612


 PERFORMANCE ORDER

  1. Details of installation of a damper krutilny fluctuations/pulley of a cranked shaft of the engine of a series 612 are shown on an illustration which all references meeting in the text concern.
  2. Remove a belt of a drive of auxiliary units (1).
  3. By means of the special adaptation (3) block a gear wreath of a flywheel / a driving disk.
  4. Turn out the central bolt (4) and remove it together with a tarelchaty washer (5).
  5. By means of a dvukhnozhechny stripper remove assembly a pulley/damper of krutilny fluctuations (6).
  6. Attentively study a condition of a nave of a damper/pulley, in case of need make replacement.
  7. Replace a forward epiploon of a cranked shaft (see. Section Removal and installation of the electromotor of shutdown of inlet port (series 612 engine)).
  8. Installation is made upside-down.

М628

Details of installation of a damper krutilny fluctuations/pulley of a driving belt of the engine of a series 628


 PERFORMANCE ORDER

  1. Details of installation of a damper krutilny fluctuations/pulley of a cranked shaft of engines of a series 628 are shown on an illustration which all references meeting in the text concern.
  2. Remove the bottom section of a noise isolation.
  3. Remove the electric fan of system of cooling.
  4. Establish the screen of protection of the К/В radiator/condenser.
  5. Remove an air sleeve of the right bottom air pipeline/cooler of a path of pressurization of air.
  6. Remove a belt of a drive of auxiliary units.
  7. Disconnect hoses of an okhladitelny path from the water pump.
  8. Holding a pulley from a provorachivaniye by means of the adaptation (2), turn out the central bolt (1).
  9. Having in case of need hooked a suitable screw-driver, remove a damper krutilny fluctuations/pulley (3).
  10. Installation is made upside-down.