Mercedes M-Class W163

since 1997 of release

Repair and car operation



Mercedes W163
+ Mercedes-Benz Cars of a class M (W163)
+ Governing bodies and receptions of safe operation
+ Current leaving and service
- Engine
   Check of kompressionny pressure in cylinders
   Engine check by means of the vacuum gage
   Replacement of a belt of a drive of auxiliary units and elements of the mechanism of its tension
   + Petrol models
   - Diesel models
      Removal and engine installation
      Removal and installation of covers of a drive of GRM
      Replacement of a gas-distributing chain
      Removal and installation of components of a drive of GRM
      Installation of base provision of camshafts
      Verification of the base provision of a balancing shaft (only series 628 engines)
      Removal and installation of GRM components
      Removal and head installation (ok) cylinders
      Removal and installation of the electromotor of shutdown of inlet port (series 612 engine)
      Removal and installation of a final collector
      Replacement of a forward epiploon of a cranked shaft
      Removal and installation of a back face cover, replacement of a back epiploon of a cranked shaft
      Removal and installation of a damper krutilny fluctuations/pulley of a driving belt
      Removal and flywheel installation / driving disk
      Removal and installation of support of a suspension bracket of the power unit
      Service of system of greasing
+ Systems of cooling, heating and air conditioner
+ the Power supply system and production of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Avtomaticheckaya transmission
+ Transmission line
+ Brake and auxiliary systems
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment


Removal and installation of a back face cover, replacement of a back epiploon of a cranked shaft

М612

Details of installation back face cover/epiploon of a cranked shaft of the engine of a series 612


 PERFORMANCE ORDER

  1. Details of installation of a back face cover / a back epiploon of a cranked shaft on engines of a series 612 are shown on an illustration which all references meeting in the text concern.
  2. Remove a flywheel / a driving disk (1) (see. Section Removal and flywheel installation / driving disk).
  3. Turn out fixing bolts and remove a face cover (2) assembled with a back epiploon of a cranked shaft, - hook a cover in the places specified by shooters, try not to damage sealing laying of the pallet of a case.
  4. Merge impellent oil.
  5. Release bolts of fastening of the pallet and merge from the last the oil remains.
  6. Carefully smooth out interfaced surfaces.
  7. Establish into place a cover with the epiploon pressed in it.

If the epiploon (3) is damaged, it is necessary to replace a cover.

  1. Establish a back sealing ring of a cranked shaft (5) (the assembly coupling (4)).
  2. Establish a flywheel / a driving disk.
  3. Tighten bolts of fastening of the pallet.
  4. Fill in in the engine fresh oil.
  5. Start the engine and check it on existence of signs of development of leaks.

М628

Details of installation back face cover/epiploon of a cranked shaft of the engine of a series 628

1 — the Face cover
2 — Bolts
3 — the Epiploon of a cranked shaft
4 — the Driving disk

5 — the Washer
6 — the Bolt
7 — Blokirator


 PERFORMANCE ORDER

  1. Details of installation of a back face cover / a back epiploon of a cranked shaft on engines of a series 628 are shown on an illustration which all references meeting in the text concern.
  2. Remove transmission (see. Head Avtomaticheckaya transmission).
  3. By means of the special adaptation (7) block a gear wreath of a driving disk.
  4. Turn out fixing bolts (6) and remove a driving disk (4) (see. Section Removal and flywheel installation / driving disk).
  5. Merge impellent oil (see. Head of the Power supply system and production of the fulfilled gases).
  6. Turn out bolts (2) and remove a face cover (1), having accurately hooked it a screw-driver with a flat sting around installation of directing plugs.
  7. Take an old epiploon (3)
  8. Carefully smooth out interfaced surfaces and, having planted on hermetic, establish a cover into place.
  9. Establish a new epiploon (3).
  10. Дейтсвуя as it should be, the return to a dismantle order, establish into place acting in film components.
  11. Start the engine and check it on existence of signs of development of leaks.