Repair and service Mercedes Benz M - the Class W163 - Installation of base provision of camshafts//since 1997 of release / mehanicm.ru

Mercedes M-Class W163

since 1997 of release

Repair and car operation



Mercedes W163
+ Mercedes-Benz Cars of a class M (W163)
+ Governing bodies and receptions of safe operation
+ Current leaving and service
- Engine
   Check of kompressionny pressure in cylinders
   Engine check by means of the vacuum gage
   Replacement of a belt of a drive of auxiliary units and elements of the mechanism of its tension
   + Petrol models
   - Diesel models
      Removal and engine installation
      Removal and installation of covers of a drive of GRM
      Replacement of a gas-distributing chain
      Removal and installation of components of a drive of GRM
      Installation of base provision of camshafts
      Verification of the base provision of a balancing shaft (only series 628 engines)
      Removal and installation of GRM components
      Removal and head installation (ok) cylinders
      Removal and installation of the electromotor of shutdown of inlet port (series 612 engine)
      Removal and installation of a final collector
      Replacement of a forward epiploon of a cranked shaft
      Removal and installation of a back face cover, replacement of a back epiploon of a cranked shaft
      Removal and installation of a damper krutilny fluctuations/pulley of a driving belt
      Removal and flywheel installation / driving disk
      Removal and installation of support of a suspension bracket of the power unit
      Service of system of greasing
+ Systems of cooling, heating and air conditioner
+ the Power supply system and production of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Avtomaticheckaya transmission
+ Transmission line
+ Brake and auxiliary systems
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment



Installation of base provision of camshafts

М612

Verification of the base provision of camshafts of the engine of a series 612


 PERFORMANCE ORDER

  1. The illustrative material on verification of the base provision of camshafts of the engine of a series 612 is presented on an illustration which all references meeting in the text concern.
  2. Remove nozzles (Y76) (see. Head of the Power supply system and production of the fulfilled gases).
  3. Uncover heads of cylinders.
  4. Having turned a cranked shaft in the normal direction, bring the piston of the first cylinder into situation VMT, - labels of a camshaft and a cover of its bearing should be combined.
  5. Block camshafts by means of the special core (3) passed through an opening in a cover of the first bearing of a shaft and filled in an opening (And) in a gear wheel (2) inlet camshafts.
  6. At the correct base installation of a label (In) gear wheels of camshafts (1 and 2) should appear combined. Besides, there should be a combination of the labels put on bodies of shaft and a cover of their bearings (arrow).
  7. In case of need remove camshafts (see. The section Removal and installation of GRM components) also establish them into place, achieving the correct combination of labels.
  8. Дейтсвуя as it should be, the return to a dismantle order, establish into place acting in film components.

М628

Installation of base provision of camshafts of the engine of a series 628

1 — the Gear wheel of an inlet camshaft
2 — the Gear wheel of a final camshaft
3 — the Inlet camshaft

4 — the Final camshaft
5 — Natyazhitel of a chain
In — Adjusting labels


 PERFORMANCE ORDER

  1. The illustrative material on adjustment of base provision of camshafts of the engine of a series 628 is presented on an illustration which all references meeting in the text concern.
  2. Remove covers of heads of cylinders.
  3. Having turned a cranked shaft in the normal direction, bring the piston of the first cylinder into situation VMT.
  4. Check the base provision of camshafts, - gear wheels should be developed by labels (In) to each other, besides, there should be a combination of the labels put on bodies of shaft and a cover of their bearings (arrow).
  5. In case of need make the corresponding adjustment.
  6. Дейтсвуя as it should be, the return to a dismantle order, establish into place acting in film components.