Mercedes M-Class W163

since 1997 of release

Repair and car operation


Mercedes W163
+ Mercedes-Benz Cars of a class M (W163)
+ Governing bodies and receptions of safe operation
+ Current leaving and service
- Engine
   Check of kompressionny pressure in cylinders
   Engine check by means of the vacuum gage
   Replacement of a belt of a drive of auxiliary units and elements of the mechanism of its tension
   + Petrol models
   - Diesel models
      Removal and engine installation
      Removal and installation of covers of a drive of GRM
      Replacement of a gas-distributing chain
      Removal and installation of components of a drive of GRM
      Installation of base provision of camshafts
      Verification of the base provision of a balancing shaft (only series 628 engines)
      Removal and installation of GRM components
      Removal and head installation (ok) cylinders
      Removal and installation of the electromotor of shutdown of inlet port (series 612 engine)
      Removal and installation of a final collector
      Replacement of a forward epiploon of a cranked shaft
      Removal and installation of a back face cover, replacement of a back epiploon of a cranked shaft
      Removal and installation of a damper krutilny fluctuations/pulley of a driving belt
      Removal and flywheel installation / driving disk
      Removal and installation of support of a suspension bracket of the power unit
      Service of system of greasing
+ Systems of cooling, heating and air conditioner
+ the Power supply system and production of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Avtomaticheckaya transmission
+ Transmission line
+ Brake and auxiliary systems
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment

Replacement of a forward epiploon of a cranked shaft

М612

Details of installation of a forward epiploon of a cranked shaft of the engine of a series 612

1 — the Belt of a drive of auxiliary units
2 — Blokirator
3 — Bolts of fastening of a blokirator

4 — the Central bolt of a pulley of a driving belt
5 — the Washer
6 — the Damper krutilny fluctuations/pulley

Details of installation of a forward epiploon of a cranked shaft of the engine of a series 612

4 — the Central bolt of a pulley of a driving belt
5 — the Washer

8 — the Epiploon
9 — Opravka


 PERFORMANCE ORDER

  1. Details of installation of a forward epiploon of a cranked shaft on engines of a series 612 are shown on illustrations which all references meeting in the text concern.
  2. Remove a belt of a drive of auxiliary units (1).
  3. By means of the special adaptation (2) block a gear wreath of a flywheel / a driving disk.
  4. Remove a damper krutilny fluctuations/pulley of a driving belt (6) (see. Section Removal and installation of a damper krutilny fluctuations/pulley of a driving belt).
  5. Having hooked a screw-driver, take an old epiploon (8) from the landing nest, - try not to damage condensed surfaces.
  6. Installation is made upside-down, - for landing of an epiploon use an opravka (9).

М628

Details of installation of a lobby face cover/epiploon of a cranked shaft of the engine of a series 628

1 — the Belt of a drive of auxiliary units
2 — the Central bolt
3 — the Damper krutilny fluctuations/pulley of a driving belt

4 — the Forward epiploon of a cranked shaft
5 — Bolts
6 — the Face cover


 PERFORMANCE ORDER

  1. Details of installation of a forward face cover / a forward epiploon of a cranked shaft on engines of a series 628 are shown on an illustration which all references meeting in the text concern.
  2. Open a cowl and fix it in vertical situation.
  3. Remove a damper krutilny fluctuations/pulley of a power shaft (3) (see. Section Removal and installation of a damper krutilny fluctuations/pulley of a driving belt).
  4. Turn out fixing bolts (5) and remove a forward face cover (6) engines.
  5. Having hooked a screw-driver, take from a landing nest in a cover an old epiploon (4).
  6. Carefully smooth out an interfaced surface of a face cover and the engine block.
  7. Put hermetic and establish a face cover on the regular place.
  8. By means of a suitable opravka plant in a cover the NEW epiploon.
  9. Further installation is made as it should be, the return to an order of dismantle of components.
  10. In summary start the engine and check it on existence of signs of development of leaks through a forward epiploon.