Mercedes M-Class W163

since 1997 of release

Repair and car operation


Mercedes W163
+ Mercedes-Benz Cars of a class M (W163)
+ Governing bodies and receptions of safe operation
+ Current leaving and service
- Engine
   Check of kompressionny pressure in cylinders
   Engine check by means of the vacuum gage
   Replacement of a belt of a drive of auxiliary units and elements of the mechanism of its tension
   - Petrol models
      Removal and engine installation
      Removal and installation of covers of a drive of GRM
      Replacement of a gas-distributing chain
      Removal and installation of components of a drive of GRM
      Installation of base provision of camshafts
      Verification of the base provision of a balancing shaft (only series 112 engines)
      Removal and installation of GRM components
      Removal and head installation (ok) cylinders
      Removal and installation of the inlet pipeline
      Removal and installation of a final collector
      Removal and installation of a face cover, replacement of a back epiploon of a cranked shaft
      Removal and installation of a damper krutilny fluctuations/pulley of a driving belt
      Removal and flywheel installation / driving disk
      Removal and installation of support of a suspension bracket of the power unit
      Service of system of greasing
   + Diesel models
+ Systems of cooling, heating and air conditioner
+ the Power supply system and production of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Avtomaticheckaya transmission
+ Transmission line
+ Brake and auxiliary systems
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment

Removal and installation of support of a suspension bracket of the power unit

М111

Back support

Details of installation of a back support of a suspension bracket of the power unit (all models)


 PERFORMANCE ORDER

  1. Details of installation of a back support of a suspension bracket of the power unit on the models equipped with the engine of a series 111, are shown on an illustration which all references meeting in the text concern.
  2. Prop up the engine.
  3. Remove a back cross-section beam of landing of the power unit (5).
  4. Remove a pillow of a support of a suspension bracket of the power unit (1).
  5. Installation is made upside-down.

Forward support

Details of installation of forward support of a suspension bracket of the power unit (the models equipped with the engine of a series 111)


 PERFORMANCE ORDER

  1. Details of installation of forward support of a suspension bracket of the power unit on the models equipped with the engine of a series 111, are shown to a naillyustratsiya which all references meeting in the text concern.
  2. Empty cooling system (see. Head Current leaving and service).
  3. Remove a broad tank (8) cooling systems.
  4. Remove assembly of the fan of system of cooling with the vyazkostny coupling.
  5. Turn out bolts of fastening of forward support (5.1 and 5.2) suspension brackets of the power unit to a car frame.
  6. Connect to the engine the winch.
  7. Hang out the power unit and remove pillows of forward support (5.1 and 5.2).
  8. Installation is made upside-down.

The pillow of the left support is marked from the forward party by a dark blue label, right - green.

М112

Back support

The design and location of a back support of the power unit are similar described above for the models equipped with the engine of a series 111.

Forward support

Details of installation of forward support of a suspension bracket of the power unit (the models equipped with engines of a series 112)


 PERFORMANCE ORDER

  1. Details of installation of forward support of a suspension bracket of the power unit on the models equipped with the engine of a series 112, are shown to a naillyustratsiya which all references meeting in the text concern.
  2. Disconnect a negative wire from the battery.
  3. Remove loker of protection of wheel arches (1).
  4. Uncover the engine.
  5. Remove an air purifier (2).
  6. Remove assembly of the fan of system of cooling with the vyazkostny coupling.
  7. Remove the thermofilter (3) of the assembly block of safety locks relays.
  8. Give nuts (4) fastenings of support (5).
  9. Connect to the engine the winch.
  10. Give nuts (6) and remove filters of pillows of support (7).
  11. Hang out the engine and remove pillows of support (5).
  12. Installation is made upside-down.

Left lateral support

Details of installation of the left lateral support of a suspension bracket of the power unit (the models equipped with engines of a series 112)

1 — the To/in Compressor
2 — the Support of the power unit

3 — the Bolt


 PERFORMANCE ORDER

  1. Details of installation of the left lateral support of a suspension bracket of the power unit on the models equipped with the engine of a series 112 are shown on an illustration which all references meeting in the text concern.
  2. Remove forward support of an engine mount (see above).
  3. Remove a belt of a drive of auxiliary units (see. Head Engine).
  4. Remove the To/in compressor (1).
  5. To Otboltita the left support (2) from an engine case also remove it from the car.
  6. Installation is made upside-down.

Right lateral support

Details of installation of the right lateral support of a suspension bracket of the power unit (the models equipped with engines of a series 112)

1 — the Support of the power unit
2 — Bolts

W11/5 — the grounding Tyre an engine/body


 PERFORMANCE ORDER

  1. Details of installation of the right lateral support of a suspension bracket of the power unit on the models equipped with the engine of a series 112 are shown on an illustration which all references meeting in the text concern.
  2. Remove forward support of an engine mount (see above).
  3. To Otboltita from the engine the tire of grounding of W11/5.
  4. To Otboltita the right support (1) from an engine case also remove it from the car.
  5. Installation is made upside-down.

М113

Back support

The design and location of a back support of the power unit are similar described above for the models equipped with the engine of a series 111.

Lobbies and lateral support

Details of installation of forward support of a suspension bracket of the power unit (the models equipped with engines of a series 113)

1 — the Connecting sleeve
2 — the Resonator
3 — fan Assembly with the vyazkostny coupling
4 — a fan Casing
5 — Bolts of fastening of a casing of the fan
6 — the Belt of a drive of auxiliary units
7 — Vozdukhootboynik
8 — the To/in Compressor
9 — Lokera
10 — Deflectors

11 — Termozashchitny the screen
12 — Nuts
13 — the Left lateral support
14 — the Right lateral support
15 — Nuts
16 — Filters of pillows
17 — Fixing bolts
18 — Pillows of forward support
W11/5 — the grounding Tyre an engine/body


 PERFORMANCE ORDER

  1. Details of installation of lobbies and lateral support of a suspension bracket of the power unit on the models equipped with the engine of a series 113, are shown on an illustration which all references meeting in the text concern.
  2. The order of performance is almost identical is similar described above for the models equipped with engines of a series 112.