Repair and service Mercedes Benz M - the Class W163 - Removal and installation of a damper krutilny fluctuations/pulley of a driving belt//since 1997 of release / mehanicm.ru

Mercedes M-Class W163

since 1997 of release

Repair and car operation



Mercedes W163
+ Mercedes-Benz Cars of a class M (W163)
+ Governing bodies and receptions of safe operation
+ Current leaving and service
- Engine
   Check of kompressionny pressure in cylinders
   Engine check by means of the vacuum gage
   Replacement of a belt of a drive of auxiliary units and elements of the mechanism of its tension
   - Petrol models
      Removal and engine installation
      Removal and installation of covers of a drive of GRM
      Replacement of a gas-distributing chain
      Removal and installation of components of a drive of GRM
      Installation of base provision of camshafts
      Verification of the base provision of a balancing shaft (only series 112 engines)
      Removal and installation of GRM components
      Removal and head installation (ok) cylinders
      Removal and installation of the inlet pipeline
      Removal and installation of a final collector
      Removal and installation of a face cover, replacement of a back epiploon of a cranked shaft
      Removal and installation of a damper krutilny fluctuations/pulley of a driving belt
      Removal and flywheel installation / driving disk
      Removal and installation of support of a suspension bracket of the power unit
      Service of system of greasing
   + Diesel models
+ Systems of cooling, heating and air conditioner
+ the Power supply system and production of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Avtomaticheckaya transmission
+ Transmission line
+ Brake and auxiliary systems
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment



Removal and installation of a damper krutilny fluctuations/pulley of a driving belt

М111

Details of installation of a damper krutilny fluctuations/pulley of a driving belt of the engine of a series 111


 PERFORMANCE ORDER

  1. Details of installation of a damper krutilny fluctuations/pulley of a driving belt of the engine of a series 111 are shown on an illustration which all references meeting in the text concern.
  2. Remove assembly of the fan of system of cooling with the vyazkostny coupling.
  3. Remove a fan casing (8).
  4. On the models equipped with the soaking-up fan, remove ventilyatorny the assembly/the К/В electric fan.
  5. At the corresponding complete set remove a belt of a drive of the To/in compressor (9а).
  6. Remove a belt of a drive of auxiliary units (9).
  7. Having turned a cranked shaft in the normal direction, bring the piston of the first cylinder into situation VMT, - the pin of a cranked shaft should be developed by a segment shponka (7) up.
  8. By means of the special adaptation (3) block a gear wreath of a flywheel / a driving disk.
  9. Turn out the central bolt (5) and remove it together with tarelchaty washers (6).
  10. By means of a dvukhnozhechny stripper remove assembly a pulley/damper of krutilny fluctuations (62).

M112/113

Details of installation of a damper krutilny fluctuations/pulley of a driving belt of engines of series 112 and 113 and forward epiploon of a cranked shaft (М113)

6 — the Assembly coupling (series 113 engines)


 PERFORMANCE ORDER

  1. Details of installation of a damper krutilny fluctuations/pulley of a driving belt of engines of series 112 and 113 and a forward epiploon (113) are shown on an illustration which all references meeting in the text concern.
  2. Remove panels of furnish of the power unit.
  3. Remove an airchipper.
  4. Remove fan assembly with the vyazkostny coupling (1) and a casing of ventilyatorny assembly (3).
  5. Remove a belt of a drive of auxiliary units (2).
  6. Having blocked a pulley for teeths of a damper of krutilny fluctuations, turn out the central bolt (4).
  7. Remove assembly of a pulley/damper of krutilny fluctuations (5).
  8. On M113 engines, having hooked a screw-driver, take a forward epiploon of a cranked shaft (7), - try not to damage a landing surface of a pulley.
  9. Installation is made upside-down, - at installation of an epiploon use a suitable opravka, do not apply any hermetics.