Repair and service Mercedes Benz M - the Class W163 - Removal and installation of pedal knot and the sensor switch of stoplights//since 1997 of release / mehanicm.ru

Mercedes M-Class W163

since 1997 of release

Repair and car operation



Mercedes W163
+ Mercedes-Benz Cars of a class M (W163)
+ Governing bodies and receptions of safe operation
+ Current leaving and service
+ Engine
+ Systems of cooling, heating and air conditioner
+ the Power supply system and production of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Avtomaticheckaya transmission
+ Transmission line
- Brake and auxiliary systems
   General information and security measures
   Check of brake system on leaks
   Check of serviceability of functioning of the vacuum amplifier of brakes
   Check of the transient valve
   Removal and installation of the main brake cylinder
   Removal and installation of the vacuum amplifier of brakes and sensor of a course of a diaphragm of BAS
   Removal and ETS/ESP hydromodulator installation
   Removal and installation of the hydraulic lines laid between GTTs and the ETS/ESP hydromodulator
   Assessment of degree of wear and replacement of brake shoes
   Replacement of brake hoses
   Removal and support installation
   Removal and installation of a brake disk
   Replacement of boots of the parking brake
   Pumping of brake system
   Removal and installation of pedal knot and sensor switch of stoplights
   Removal and installation of a pedal of raising of the parking brake
   Removal and installation of hummock assembly of a drive of the parking brake
   Adjustment of a drive of the parking brake
   Removal and installation of wheel ABS/ETS/ESP sensors
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment



Removal and installation of pedal knot and sensor switch of stoplights

Pedal knot

Details of installation of pedal knot

Design of pedal knot

10 — the Holder
11 — ГТЦ
12 — the Lock ring
13 — the Nut
15 — the Returnable spring
18 — the Auxiliary spring
25 — the Pedal of a foot brake
26 — the Lock ring
27 — the Washer
28 — the Plug

29 — the Lock ring
30 — a pusher Rod
31 — the Spring plate
32 — the Clamp
33 — a coupling Pedal
34 — the Lock ring
35 — the Washer
37 — the Overlay of a block of a brake pedal
38 — the Overlay of a block of a pedal of coupling
44 — the Plug


 PERFORMANCE ORDER

See also Section Removal and installation of the main cylinder.

  1. Details of installation of pedal knot are shown on an illustration which all references meeting in the text concern.
  2. Uncover at the left under the dashboard and the left forward rug.
  3. Remove a hose connecting the tank of brake liquid to GTTs (11).
  4. Disconnect from GTTs (11) the hydraulic line (17).
  5. Disconnect electroconducting from the sensor switch of stoplights.
  6. At the corresponding complete set disconnect electroconducting from the sensor of a pedal of coupling.
  7. Disconnect from a pedal of a foot brake a returnable spring.
  8. Take a blokirator (22) and remove from a brake pedal assembly of a bearing arm.
  9. Give nuts (24) fastenings of the holder of pedal assembly to a partition of an impellent compartment.
  10. Turn out the top bolt (23) fastenings of a pedal.
  11. Having submitted pedal assembly back, remove its basic plate from fixing hairpins, then at an angle take it from a foot well.
  12. In case of need make dismantling of pedal knot.
  13. Installation is made upside-down.

Sensor switch of stoplights

Details of installation of the sensor switch of stoplights


 PERFORMANCE ORDER

  1. Details of installation of the sensor switch of stoplights are shown on an illustration which all references meeting in the text concern.
  2. Uncover at the left under the dashboard.
  3. Disconnect from the sensor switch of stoplights (S9) electroconducting.
  4. Release a clamp (2) and remove the sensor switch (S9).
  5. Extend a plunzher (1) sensor against the stop outside, wring out a pedal (24) and establish the sensor switch on the regular place, having tracked reliability of a zashchelkivaniye of a clamp (2), adjustment of the sensor switch occurs automatically.
  6. Further installation is made as it should be, the return to an order of dismantle of components.