Mercedes M-Class W163

since 1997 of release

Repair and car operation



Mercedes W163
+ Mercedes-Benz Cars of a class M (W163)
+ Governing bodies and receptions of safe operation
+ Current leaving and service
+ Engine
+ Systems of cooling, heating and air conditioner
+ the Power supply system and production of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Avtomaticheckaya transmission
- Transmission line
   + Coupling
   + Driveshafts
   + Power shafts
   - Transfer case and differentials
      Removal and installation of the module of management of a transfer case
      Removal and installation of a transfer case
      Replacement of an epiploon of an entrance shaft of a transfer case
      Replacement of an epiploon of a target flange of the back driveshaft
      Replacement of an epiploon of a forward target shaft
      Removal and installation of the servomotor of switching of modes of a transfer case
      Removal and installation of a chain drive of a transfer case
      Removal and installation of a forward target shaft of a transfer case
      Removal and installation of assembly of a planetary reducer of interaxal differential of a transfer case
      Removal and installation of assembly of bearing assembly of a transfer case
      Removal and installation of the oil pump of a transfer case
      Removal and installation of the mechanism of switching of a transfer case
      Removal and installation of a reduktsionny gear wheel of a transfer case
      Replacement of lateral epiploons of differentials
      Replacement of epiploons of leading gear wheels of differentials
      Removal and installation of differentials
+ Brake and auxiliary systems
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment


Removal and installation of differentials

In total самоконтрящиеся bolts and nuts are subject to replacement without fail!

Forward differential

Details of installation of forward differential


 PERFORMANCE ORDER

  1. Details of installation of forward differential are shown on an illustration which all references meeting in the text concern.
  2. Remove forward wheels.
  3. Turn out the corresponding stopper and merge from differential oil.
  4. To Otboltita the forward driveshaft from a connecting flange of a leading gear wheel, - tie up a shaft to a frame.
  5. By means of a stripper liberate both top spherical support from the corresponding cross-section levers of a suspension bracket, check a condition of boots, estimate degree of wear of support, in case of need make replacement.
  6. Remove panels of furnish of an impellent compartment.
  7. Liberate from differential both power shafts, - try not to damage guards.
  8. Disconnect from a differential case a ventilating hose.
  9. Turn out fixing bolts (14а) and remove assembly of forward differential (14).
  10. Installation is made upside-down.
  11. In summary check differential on existence of signs of development of leaks.

Back differential

Details of installation of back differential

1s — the Guard
37 — Power shafts
50 — Back differential
50а — Fixing bolts
50d — Covers

55 — the Ventilating hose
106 — the Back driveshaft
And — release Models till 05.98
And — release Models from 06.98


 PERFORMANCE ORDER

  1. To detail of installation of back differential it is presented on an illustration which all references meeting in the text concern.
  2. Remove power shafts (37).
  3. Turn out fixing bolts and disconnect the driveshaft (106) from a connecting flange of a leading gear wheel of back differential (50), - tie up a shaft to a car frame.
  4. Liberate a ventilating hose (55) of clamps on a fuel tank, - except the models equipped with an additional fuel tank (ML 55 AMG) on which the hose can be released only after differential lowering.
  5. Remove covers (50d) fixing bolts.
  6. On models ML of 55 AMG remove a guard (1s), established on the left side from differential assembly.
  7. Prop up assembly of back differential (50).
  8. Remove elements of a suspension bracket of fastening of back differential to the holder of the bridge (А/В).
  9. Turn out fixing bolts (50а), omit assembly of differential (50) down and take it from under the car, - on models ML of 55 AMG do not forget to liberate after lowering of assembly of differential from clamps on a fuel tank a ventilating hose.
  10. Estimate a condition of forward and back rubber support in the holder of the back bridge, in case of need make their replacement.
  11. Installation is made upside-down.
  12. In summary check differential on existence of signs of development of leaks.