Mercedes M-Class W163

since 1997 of release

Repair and car operation



Mercedes W163
+ Mercedes-Benz Cars of a class M (W163)
+ Governing bodies and receptions of safe operation
+ Current leaving and service
+ Engine
+ Systems of cooling, heating and air conditioner
+ the Power supply system and production of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Avtomaticheckaya transmission
- Transmission line
   + Coupling
   + Driveshafts
   + Power shafts
   - Transfer case and differentials
      Removal and installation of the module of management of a transfer case
      Removal and installation of a transfer case
      Replacement of an epiploon of an entrance shaft of a transfer case
      Replacement of an epiploon of a target flange of the back driveshaft
      Replacement of an epiploon of a forward target shaft
      Removal and installation of the servomotor of switching of modes of a transfer case
      Removal and installation of a chain drive of a transfer case
      Removal and installation of a forward target shaft of a transfer case
      Removal and installation of assembly of a planetary reducer of interaxal differential of a transfer case
      Removal and installation of assembly of bearing assembly of a transfer case
      Removal and installation of the oil pump of a transfer case
      Removal and installation of the mechanism of switching of a transfer case
      Removal and installation of a reduktsionny gear wheel of a transfer case
      Replacement of lateral epiploons of differentials
      Replacement of epiploons of leading gear wheels of differentials
      Removal and installation of differentials
+ Brake and auxiliary systems
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment



Replacement of an epiploon of a forward target shaft

Replacement of an epiploon of a forward target shaft

1 — the Transfer case
2 — a case Cover
3 — the Drain stopper
4 — the Jellied stopper
5 — Bolts
6 — Bolts
7 — the Sensor of turns

8 — the Target flange of the back driveshaft
9 — the Sealing ring
10 — the Washer
11 — the Nut
12 — the Servomotor
010 — the Assembly stand
020 — the Basic plate

Replacement of an epiploon of a forward target shaft

1 — the Transfer case
13 — Asterisks of chain transfer
13а — the Driving chain
14 — the Lock ring
15 — the Ball bearing

16 — the Forward target shaft
17 — the Epiploon
18 — the Planetary reducer
19 — the Back target shaft

Replacement of an epiploon of a forward target shaft

17 — the Epiploon

030 — Opravka


 PERFORMANCE ORDER

  1. The illustrative material on replacement of an epiploon of a forward target shaft of a transfer case is presented on illustrations which all references meeting in the text concern.
  2. Turn out a stopper (3) and merge from a case of a transfer case oil.
  3. Remove a transfer case (1) (see. The section Removal and installation of a transfer case) also fix it at the assembly stand (010) by means of a basic plate (020).
  4. Remove a back target flange (8) (see. Section Replacement of an epiploon of a target flange of the back driveshaft).
  5. Turn out fixing bolts (6) and remove the servomotor (12) assembled with the sensor of turns (7).
  6. Having pulled outside, take the sensor of turns (7).
  7. Turn out bolts (5) and uncover (2).
  8. Having pulled outside, remove asterisks (13) assembled with a driving chain (13а).
  9. Remove a lock ring (14) and remove a target shaft of a drive of a forward axis (16).

At removal of a lock ring hold a shaft motionlessly.

  1. Having hooked a suitable screw-driver, take an epiploon (17) forward target shaft from the landing nest and plant on its place new, having used a suitable opravka (030), - before a zastukivaniye of an epiploon fix assembly of a planetary reducer (18) for the purpose of prevention of its loss.
  2. Establish into place a forward target shaft (16) and fix it a lock ring (14), having tracked reliability of landing of the last in a reception flute.
  3. Establish assembly of a chain drive (13 and 13а).
  4. To Priboltita a cover (2), previously having smoothed out interfaced surfaces and having imposed suitable hermetic.
  5. Establish into place the servomotor (12) and the sensor of turns (7), tighten fixing bolts (6).
  6. Establish a flange of the back driveshaft (see. Section Replacement of an epiploon of a target flange of the back driveshaft).
  7. Fill in in a transfer case fresh oil to level of the bottom cut of a jellied/control opening.
  8. In summary start the engine and check a transfer case on existence of signs of development of leaks.