Repair and service Mercedes Benz M - the Class W163 - Removal and installation of the lock of blocking of a steering column//since 1997 of release / mehanicm.ru

Mercedes M-Class W163

since 1997 of release

Repair and car operation



Mercedes W163
+ Mercedes-Benz Cars of a class M (W163)
+ Governing bodies and receptions of safe operation
+ Current leaving and service
+ Engine
+ Systems of cooling, heating and air conditioner
+ the Power supply system and production of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Avtomaticheckaya transmission
+ Transmission line
+ Brake and auxiliary systems
- Suspension bracket and steering
   + Forward suspension bracket
   + Back suspension bracket
   - Steering
      Filling and "pumping" of the steering pump
      Check of a pressure of the steering pump
      Replacement of a collar of fastening of a hose of a path of cooling of GUR liquid
      Assessment of a condition of hinges of steering drafts and boots of a case of reechny transfer
      Removal and installation of the steering pump
      Replacement of boots of a case of the steering mechanism
      Removal and installation of tips of steering draft
      Removal installation of entrance knot of the steering mechanism
      Removal and installation of the steering mechanism
      Dismantling of a mechanical regulator of a steering column
      Removal and installation of a steering wheel and spiral contact drum of a steering column
      Removal and installation of the cylinder of the lock of ignition
      Removal and installation of the lock of blocking of a steering column
      Removal and installation and shirts of a steering column
   + suspension bracket Geometry
+ Body
+ Onboard electric equipment



Removal and installation of the lock of blocking of a steering column

Details of installation of the lock are shown on an illustration which all references meeting in the text concern.

Details of installation of the lock of blocking of a steering column

and — I Will corrode switch electroconductings
b — the Contact socket

with — Transponder

Removal

 PERFORMANCE ORDER

  1. Remove the lock (36) cylinder (see. Section Removal and installation of the cylinder of the lock of ignition).
  2. Remove a steering wheel (120) and a spiral contact drum (see. Section Removal and installation of a steering wheel and spiral contact drum of a steering column).
  3. Remove combined podrulevy the switch (S4) (see. Head Onboard electric equipment).
  4. Separate the facing panel (88).
  5. Disunite the socket (and) the contact switch (37q) the adjusting lever (93).
  6. On models from AT remove from the lock of a steering column a switching blokirator, - compress latches and pull a blokirator back, removing it from fixing clamps.
  7. Having submitted forward, remove from the lock a transponder (c).
  8. In order to avoid damage шлицов a steering shaft at knocking-out of a cylindrical pin (37s) screw a bolt (32с).
  9. Lower down the adjusting lever (93).
  10. By means of a suitable drift beat out from zamkovy assembly (37) cylindrical pin (37s), - the bottom directing pin will be put out of action.
  11. Having released a clamp, disunite the contact socket (b).
  12. Remove the lock (37).
  13. Remove the contact switch (37q).

Installation

 PERFORMANCE ORDER

  1. Connect the contact switch (37q) to the new lock (37).
  2. Plant into place the socket (b), - track reliability of a zashchelkivaniye of a clamp.
  3. Put the new lock on a steering column, having tracked correctness of landing of assembly (arrow).
  4. Fill in the lock (37) a cylindrical pin (37s), - compress the top and bottom sections of the lock nippers.
  5. Plant into place the contact switch (32q), make sure of serviceability of its functioning.
  6. Turn out a bolt (32с).
  7. Plant on the lock (37) a transponder (c).
  8. On models from AT connect to the lock a blokirator of switchings.
  9. Connect electroconducting (and) to the contact switch of the adjusting lever.
  10. Establish the facing panel (88).
  11. Establish the combined switch (S4).
  12. Establish a spiral contact drum and a steering wheel (120) (see. Section Removal and installation of a steering wheel and spiral contact drum of a steering column).
  13. Establish the lock (36) cylinder (see. Section Removal and installation of the cylinder of the lock of ignition).
  14. Fix a steering column, having lifted up the adjusting lever (93).