Repair and service Mercedes Benz M - the Class W163 - Removal and installation of a steering wheel and a spiral contact drum of a steering column//since 1997 of release / mehanicm.ru

Mercedes M-Class W163

since 1997 of release

Repair and car operation



Mercedes W163
+ Mercedes-Benz Cars of a class M (W163)
+ Governing bodies and receptions of safe operation
+ Current leaving and service
+ Engine
+ Systems of cooling, heating and air conditioner
+ the Power supply system and production of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Avtomaticheckaya transmission
+ Transmission line
+ Brake and auxiliary systems
- Suspension bracket and steering
   + Forward suspension bracket
   + Back suspension bracket
   - Steering
      Filling and "pumping" of the steering pump
      Check of a pressure of the steering pump
      Replacement of a collar of fastening of a hose of a path of cooling of GUR liquid
      Assessment of a condition of hinges of steering drafts and boots of a case of reechny transfer
      Removal and installation of the steering pump
      Replacement of boots of a case of the steering mechanism
      Removal and installation of tips of steering draft
      Removal installation of entrance knot of the steering mechanism
      Removal and installation of the steering mechanism
      Dismantling of a mechanical regulator of a steering column
      Removal and installation of a steering wheel and spiral contact drum of a steering column
      Removal and installation of the cylinder of the lock of ignition
      Removal and installation of the lock of blocking of a steering column
      Removal and installation and shirts of a steering column
   + suspension bracket Geometry
+ Body
+ Onboard electric equipment



Removal and installation of a steering wheel and spiral contact drum of a steering column

Steering wheel

Removal/installation of a steering wheel

Removal/installation of a steering wheel

Removal/installation of a steering wheel

Removal/installation of a steering wheel


 PERFORMANCE ORDER

  1. The corresponding illustrative material is presented on illustrations which all references meeting in the text concern.
  2. Disconnect a negative wire from the battery.
  3. Remove the module of a driver's face-to-face safety cushion (120) (see. Head Onboard electric equipment).
  4. Disunite contact sockets of electroconducting of a horn (38b and 38с).
  5. Bring forward wheels of the car into rectilinear situation, then block a steering column by key extraction from the ignition lock.
  6. Holding a steering wheel (32), turn out a bolt (32с), - the bolt is subject to replacement without fail.
  7. Accurately remove a steering wheel (32), - try not to damage electroconducting.
  8. Check a condition of a spiral contact drum (А45) of electroconducting of a horn and a safety cushion, in case of need make its replacement (see below).
  9. Installation is made upside-down, - track correctness of combination of landing marking.

Spiral contact drum

Removal/installation of a spiral contact drum

Removal/installation of a spiral contact drum

Removal/installation of a spiral contact drum)


 PERFORMANCE ORDER

  1. The corresponding illustrative material is presented on illustrations which all references meeting in the text concern.
  2. Remove a steering wheel (see above).
  3. Weaken screws (32h) exactly so to provide possibility of removal of a contact drum (А45), - bolts at the same time play a role of protection against a provorachivaniye.
  4. Accurately remove assembly of a spiral drum (А45) from a pipe of a shirt of a steering column.
  5. Disunite the socket (38d) electroconductings of drum-type assembly (А45).
  6. Estimate a condition of a drum (А45), - top (32f) and bottom (32g) sections of drum-type assembly strongly fasten to each other by means of clamps. Replace defective components, - try not to allow jammings of a spiral spring (32е) at connection of sections of a drum.
  7. Installation is made upside-down. Track completeness of landing of a drum (А45), - deepening should be combined with a lock uvula (shooter), in case of need make centering.