Mercedes M-Class W163

since 1997 of release

Repair and car operation



Mercedes W163
+ Mercedes-Benz Cars of a class M (W163)
+ Governing bodies and receptions of safe operation
+ Current leaving and service
+ Engine
- Systems of cooling, heating and air conditioner
   + System of cooling of the engine
   - Systems of ventilation, heating and air conditioning
      General information and security measures
      Removal and control panel installation by functioning of systems of heating/ventilation/air conditioning (for models 163.113/136/154/172/174 on 31.8.01)
      Removal and installation of the salonny filter
      Removal and installation of the fan of the heater/conditioner of air and its resistive assembly
      Removal and installation of the heat exchanger of a heater
      Removal and installation of the step-by-step electromotor of a drive of a zaslonka of switching of modes of air circulation
      Removal and installation of the electromotor of a drive of a mixing zaslonka
      Removal and installation of a casing of the heat exchanger of the heater/evaporator of the conditioner of air
      Fast check of serviceability of functioning of central air of air
      Removal and installation of auxiliary ventilyatorny assembly, - models 163.136/154/157/172 of the corresponding complete set
      Removal and installation of the podsasyvayushchy fan of the sensor of temperature of salonny air, - models 163.113/136/154/157/172/174 with 1.9.99 on 31.8.01
      Removal and installation of the sensor of temperature of external air, - except models 163.128
      Removal and installation of the sensor of temperature of the evaporator
      Removal of a casing of the To/in evaporator
      Removal and To/in evaporator installation
      Removal and To/in condenser installation
      Removal and installation of the broad valve
      Removal and receiver dehumidifier installation
      Removal and installation of the module of management To/in (for models 163.113/136/154/172/174 on 31.8.01)
+ the Power supply system and production of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Avtomaticheckaya transmission
+ Transmission line
+ Brake and auxiliary systems
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
Сетка дорожная цена за тонну на сайте metallsetka.ru.



Removal and To/in condenser installation

Details of installation of the To/in condenser

1 — the Top forward cross-section beam of a frame
2 — the Bolt
3 — Bolts
4 — the Rubber sealant

5 — the Condenser
6 — the Bolt
7 — the Radiator
М4 — Auxiliary ventilyatorny assembly (at the corresponding complete set)


 PERFORMANCE ORDER

All sealing elements are subject to replacement without fail.

  1. Details of installation of the To/in condenser are shown on an illustration which all references meeting in the text concern.
  2. On models 163.136/154/157/172 remove auxiliary ventilyatorny assembly (М4) (see. The section Removal and installation of auxiliary ventilyatorny assembly, - models 163.136/154/157/172 of the corresponding complete set).
  3. On models 163.112/128 remove a cooler of a path of pressurization of air (see. Section Removal and installation of a radiator of system of cooling).
  4. In the conditions of a workshop of car-care center make the К/В system discharge.
  5. Verify the screw (2) and disconnect the refrigerator line from a receiver dehumidifier.
  6. Turn out the screw (6) and disconnect the refrigerator line from the condenser (5).
  7. Remove from a radiator of system of cooling (7) rubber sealant (4).
  8. Turn out fixing bolts (3) and, having pulled up, remove the To/in condenser (5).
  9. Installation is made upside-down, - filling of central air of air should be made in the conditions of a car-care center workshop.