Repair and service Mercedes Benz M - the Class W163 - Removal and installation of the sensor of temperature of external air, - except models 163.128//since 1997 of release / mehanicm.ru

Mercedes M-Class W163

since 1997 of release

Repair and car operation



Mercedes W163
+ Mercedes-Benz Cars of a class M (W163)
+ Governing bodies and receptions of safe operation
+ Current leaving and service
+ Engine
- Systems of cooling, heating and air conditioner
   + System of cooling of the engine
   - Systems of ventilation, heating and air conditioning
      General information and security measures
      Removal and control panel installation by functioning of systems of heating/ventilation/air conditioning (for models 163.113/136/154/172/174 on 31.8.01)
      Removal and installation of the salonny filter
      Removal and installation of the fan of the heater/conditioner of air and its resistive assembly
      Removal and installation of the heat exchanger of a heater
      Removal and installation of the step-by-step electromotor of a drive of a zaslonka of switching of modes of air circulation
      Removal and installation of the electromotor of a drive of a mixing zaslonka
      Removal and installation of a casing of the heat exchanger of the heater/evaporator of the conditioner of air
      Fast check of serviceability of functioning of central air of air
      Removal and installation of auxiliary ventilyatorny assembly, - models 163.136/154/157/172 of the corresponding complete set
      Removal and installation of the podsasyvayushchy fan of the sensor of temperature of salonny air, - models 163.113/136/154/157/172/174 with 1.9.99 on 31.8.01
      Removal and installation of the sensor of temperature of external air, - except models 163.128
      Removal and installation of the sensor of temperature of the evaporator
      Removal of a casing of the To/in evaporator
      Removal and To/in evaporator installation
      Removal and To/in condenser installation
      Removal and installation of the broad valve
      Removal and receiver dehumidifier installation
      Removal and installation of the module of management To/in (for models 163.113/136/154/172/174 on 31.8.01)
+ the Power supply system and production of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Avtomaticheckaya transmission
+ Transmission line
+ Brake and auxiliary systems
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment



Removal and installation of the sensor of temperature of external air, - except models 163.128

Details of installation of the sensor of temperature of external air

Details of installation of the sensor of temperature of external air

Shooters — Screws of fastening of the dashboard to racks And


 PERFORMANCE ORDER

  1. Details of installation of the sensor of temperature of external air are shown on illustrations which all references meeting in the text concern.
  2. Empty cooling system (see. Head of the Power supply system and production of the fulfilled gases).
  3. Turn out fixing bolts and remove from a back partition of an impellent compartment a broad tank of system of cooling (1).
  4. Disconnect hoses of an okhladitelny path (2) from the heater heat exchanger.
  5. In the conditions of a workshop of car-care center make a discharge of central air of air.
  6. Uncover the broad valve (4).
  7. Give a nut (3) fastenings of the broad valve (4).
  8. Disconnect from the broad valve refrigerator lines.
  9. Remove assembly of a drive of screen wipers.
  10. Give nuts (5) dashboards on a partition of an impellent compartment.
  11. Remove panels of furnish of racks And.
  12. Give the plastic nuts of the panel of fastening of the panel of furnish located at the left under the dashboard.
  13. Remove the panel of furnish of a foot well.
  14. Remove rubber caps and turn out screws of fastening of panelipribor to racks And (shooters).
  15. Remove assembly of the central console (see. Head Body).
  16. Turn out a bolt (6) under the dashboard.
  17. Delay the dashboard back and develop so that access to its back party opened.
  18. Disunite the contact socket of electroconducting (B10/5x1) of the sensor of temperature of external air.
  19. Disconnect a cable going from the sensor to a casing of the evaporator of the conditioner of the air/heat exchanger of a heater.
  20. Take the sensor of temperature of external air (B10/5) from an air sleeve.
  21. Installation is made upside-down, - filling of central air should be made in the conditions of a car-care center workshop.
  22. In summary check cooling system on existence of signs of development of leaks.