Repair and service Mercedes Benz M - the Class W163 - Removal of a casing of the To/in evaporator//since 1997 of release / mehanicm.ru

Mercedes M-Class W163

since 1997 of release

Repair and car operation



Mercedes W163
+ Mercedes-Benz Cars of a class M (W163)
+ Governing bodies and receptions of safe operation
+ Current leaving and service
+ Engine
- Systems of cooling, heating and air conditioner
   + System of cooling of the engine
   - Systems of ventilation, heating and air conditioning
      General information and security measures
      Removal and control panel installation by functioning of systems of heating/ventilation/air conditioning (for models 163.113/136/154/172/174 on 31.8.01)
      Removal and installation of the salonny filter
      Removal and installation of the fan of the heater/conditioner of air and its resistive assembly
      Removal and installation of the heat exchanger of a heater
      Removal and installation of the step-by-step electromotor of a drive of a zaslonka of switching of modes of air circulation
      Removal and installation of the electromotor of a drive of a mixing zaslonka
      Removal and installation of a casing of the heat exchanger of the heater/evaporator of the conditioner of air
      Fast check of serviceability of functioning of central air of air
      Removal and installation of auxiliary ventilyatorny assembly, - models 163.136/154/157/172 of the corresponding complete set
      Removal and installation of the podsasyvayushchy fan of the sensor of temperature of salonny air, - models 163.113/136/154/157/172/174 with 1.9.99 on 31.8.01
      Removal and installation of the sensor of temperature of external air, - except models 163.128
      Removal and installation of the sensor of temperature of the evaporator
      Removal of a casing of the To/in evaporator
      Removal and To/in evaporator installation
      Removal and To/in condenser installation
      Removal and installation of the broad valve
      Removal and receiver dehumidifier installation
      Removal and installation of the module of management To/in (for models 163.113/136/154/172/174 on 31.8.01)
+ the Power supply system and production of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Avtomaticheckaya transmission
+ Transmission line
+ Brake and auxiliary systems
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment



Removal of a casing of the To/in evaporator

Details of installation of a casing of the To/in evaporator

1 — the Casing of the evaporator of the conditioner/heat exchanger of a heater
2 — the Sound-proof panel
3 — the Air distributor
4 — the Holder of the dashboard
5 — the Contact socket of electroconducting of the fan of a heater
6 — the Contact socket of resistive assembly of the fan

B10/6kh1 — the Contact socket of the sensor of temperature of the evaporator
M16/8 — Elektromotor of a drive of a mixing zaslonka
М39 — the Step-by-step electromotor of a drive of a zaslonka of switching of modes of circulation
N15/3 — the Module of management of ETC
N19 — the management Module To/in

Details of installation of a casing of the To/in evaporator


 PERFORMANCE ORDER

All sealing elements are subject to replacement without fail.

  1. Details of installation of a casing of the evaporator of the conditioner of the air/heat exchanger of a heater are shown on illustrations which all references meeting in the text concern.
  2. Empty cooling system (see. Head of the Power supply system and production of the fulfilled gases).
  3. Disconnect perelivny a hose of system of cooling from a board of the storage battery.
  4. Release fixing a collar and disconnect the top hose from the electric water pump.
  5. Give fixing nuts and remove a broad tank of system of cooling from a partition of an impellent compartment. Take a tank aside.
  6. Disconnect hoses of an okhladitelny path (17) from the heater heat exchanger.
  7. In the conditions of a workshop of car-care center make the К/В system discharge.
  8. Give самоконтрящуюся a nut (16) broad valves (15).
  9. Disconnect from the broad valve (15) low-pressure head (13) and high-pressure head (14) lines of a refrigerator path.
  10. Remove the holder of the dashboard (4).
  11. Liberate from clamps the module of management of ETC (N15/3).
  12. Disconnect electroconducting from the electromotor of a drive of a mixing zaslonka of air (M16/8).
  13. Disconnect electroconducting from the step-by-step electromotor of a drive of a zaslonka of switching of modes of air circulation (М39).
  14. Disunite the contact socket of electroconducting (B10/6kh1) of the sensor of temperature of the evaporator.
  15. Disconnect electroconducting from resistive assembly of the fan of a heater (6).
  16. Disconnect electroconducting from the fan of a heater (5).
  17. Remove the management module In (N19).
  18. Liberate from intermediate clamps on a casing of the evaporator (1) cable plait.
  19. Remove the sound-proof panel (2).
  20. Disconnect a drainage hose from the lower part of a casing of the To/in evaporator (1).
  21. Remove a casing (1).
  22. Installation is made upside-down, - filling of central air of air should be made in the conditions of a car-care center workshop.
  23. In summary check cooling system on existence of signs of development of leaks.