Mercedes M-Class W163

since 1997 of release

Repair and car operation



Mercedes W163
+ Mercedes-Benz Cars of a class M (W163)
+ Governing bodies and receptions of safe operation
+ Current leaving and service
+ Engine
+ Systems of cooling, heating and air conditioner
+ the Power supply system and production of the fulfilled gases
- Systems of electric equipment of the engine
   + ignition and engine management Systems
   + System of preheat of the diesel engine
   + Diagnostics of systems of electronic control and diagnostic equipment
   - Charge and start systems
      General information
      The storage battery - the general information, recommendations about service
      Charge system - general information and security measures
      Check of system of a charge
      Removal and generator installation
      Removal and installation of a driving pulley of the generator
      Removal and installation of a regulator of tension
      System of start of the engine - the general information and precautionary measures
      Removal and starter installation
+ Manual box of gear shifting
+ Avtomaticheckaya transmission
+ Transmission line
+ Brake and auxiliary systems
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
Medicine and health news .



Removal and starter installation

Models 163.136 and 163.113

Details of installation of a starter on models 163.136 and 163.113 (engines of series 111 and 612)

1 — the Plug 30
2 — the Plug 50

3 — Screws
М1 — the Starter


 PERFORMANCE ORDER

  1. Details of installation of a starter on models 163.136 and 163.113 are shown on an illustration which all references meeting in the text concern.
  2. Disconnect a negative wire from the battery.
  3. Remove the left forward wheel and a loker of protection of a wheel arch.
  4. Disconnect electroconducting from plugs 30 (1) and 50 (2) starter.
  5. Turn out fixing bolts (3) and remove assembly of a starter (М1).
  6. Installation is made upside-down, do not forget to execute the procedures interfaced to connection of the battery.

Models 163.154/157/173/174/175

Details of installation of a starter on models 163.154/157/173/174/175 (engines of series 112 and 113)

1 — the Plug 30
2 — the Plug 50
3 — Bolts
4 — the Nut

5 — the Guard of a support of a suspension bracket of the power unit
6 — the Nut
7 — the Washer
М1 — the Starter


 PERFORMANCE ORDER

  1. Details of installation of a starter on models 163.154/157/173/174/175 are shown on an illustration which all references meeting in the text concern.
  2. Disconnect a negative wire from the battery.
  3. Remove the right forward wheel and a loker of protection of a wheel arch.
  4. Give a fixing nut (6) and remove a guard of a support of a suspension bracket of the power unit (5).
  5. Disconnect electroconducting from plugs 30 (1) and 50 (2) starter.
  6. Turn out fixing bolts (3) and remove assembly of a starter (М1).
  7. Installation is made upside-down, do not forget to execute the procedures interfaced to connection of the battery.

Models 163.128

Details of installation of a starter on models 163.128 (series 628 engines)

1 — Nizhny a branch pipe of an air path
2 — the Plug 50

3 — the Plug 30
М1 — the Starter

Details of installation of a starter on models 163.128 (series 628 engines)

4 — the Bolt


 PERFORMANCE ORDER

  1. Details of installation of a starter on models 163.128 are shown on illustrations which all references meeting in the text concern.
  2. Disconnect a negative wire from the battery.
  3. Remove the bottom section of a noise isolation.
  4. Remove the right bottom branch pipe of an air path (1) and take him aside, without disconnecting from an air line.
  5. Remove a protective cap and disconnect electroconducting from plugs 20 (3) and 50 (2) starter.
  6. Turn out fixing bolts (4) and remove assembly of a starter (М1).
  7. Installation is made upside-down, do not forget to execute the procedures interfaced to connection of the battery.